Enterasys Securestack C3 - Revision history

Adj: /* Let's span our trees! */

2015-09-15T16:08:02Z

Let's span our trees!

← Older revision		Revision as of 16:08, 15 September 2015
Line 444:		Line 444:
	Turn on Multiple Spanning Tree Protocol (802.1s)		Turn on Multiple Spanning Tree Protocol (802.1s)
	C3(rw)->'''set spantree version mstp'''		C3(rw)->'''set spantree version mstp'''

			''Yeah, this needs a great deal of filling out. Sorry.''

Adj: /* Layer 3 (IP) services for the VLANs */

2015-06-29T15:35:31Z

Layer 3 (IP) services for the VLANs

← Older revision		Revision as of 15:35, 29 June 2015
Line 363:		Line 363:
	Changing protocol mode will reset ip configuration.		Changing protocol mode will reset ip configuration.
	Are you sure you want to continue? (y/n)'''y'''		Are you sure you want to continue? (y/n)'''y'''


	C3(rw)->'''router'''		C3(rw)->'''router'''
	C3(rw)->router>'''enable'''		C3(rw)->router>'''enable'''

Adj: /* Layer 3 (IP) services for the VLANs */

2015-06-29T15:34:35Z

Layer 3 (IP) services for the VLANs

← Older revision		Revision as of 15:34, 29 June 2015
Line 358:		Line 358:

	C3(rw)->		C3(rw)->
			And that should be it, right? Well, no, it isn't. Remember how the switch has an IP on the default VLAN, too? The layer 3 router can't do anything with that. We need to get it an IP on VLAN 1 so that the DHCP relaying can work:

			C3(rw)->'''set ip protocol none'''
			Changing protocol mode will reset ip configuration.
			Are you sure you want to continue? (y/n)'''y'''

			C3(rw)->'''router'''
			C3(rw)->router>'''enable'''
			C3(rw)->router#'''configure terminal'''
			Enter configuration commands:
			C3(rw)->router(Config)#'''interface vlan 1'''
			C3(rw)->router(Config-if(Vlan 1))#'''ip address 172.16.0.254 255.255.255.0'''
			C3(rw)->router(Config-if(Vlan 1))#'''no shutdown'''
			C3(rw)->router(Config-if(Vlan 1))#'''exit'''
			C3(rw)->router(Config)#'''exit'''
			C3(rw)->router#'''show ip route'''

			Codes: C - connected, S - static, R - RIP, O - OSPF, IA - OSPF interarea
			N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
			E1 - OSPF external type 1, E2 - OSPF external type 2
			E - EGP, i - IS-IS, L1 - IS-IS level-1, LS - IS-IS level-2
			* - candidate default, U - per user static route

			C 172.16.0.0/24 [0/1] directly connected, Vlan 1
			C 172.20.0.0/24 [0/1] directly connected, Vlan 100
			C3(rw)->router#'''exit'''
			C3(rw)->router>'''exit'''
			C3(rw)->'''show ip route'''

			INET route table
			Destination Gateway Flags Use If Metric
			127.0.0.1 127.0.0.1 UH 0 lo0 5
			172.16.0.0/24 127.0.0.1 UC 1 rt2 5
			172.16.0.254 127.0.0.1 UH 0 lo0 5
			172.20.0.0/24 127.0.0.1 UC 0 rt1 5
			172.20.0.254 127.0.0.1 UH 0 lo0 5

			INET6 route table
			Destination Gateway Flags Use If Metric
			::1 ::1 UH 0 lo0 5
			FE80::21F:45FF:FE85:1738%host ::1 UH 0 lo0 5

			C3(rw)->

			Added bonus here: the switch hasn't pulled a default route from the DHCP server any more.

	== What time is it? It's time for lunch! ==		== What time is it? It's time for lunch! ==

Adj: /* Assign an IP address to the switch */

2015-06-29T05:05:01Z

Assign an IP address to the switch

← Older revision		Revision as of 05:05, 29 June 2015
Line 61:		Line 61:
	C3(rw)->		C3(rw)->

	'''Except:''' You really want to put an IP address on VLAN 1 instead. See below for how that works.		'''Except:''' You really want to put an IP address on VLAN 1 instead. See below for how that works. Static IP for the switch management works just fine here for now.

	=== Or set it to be a DHCP client ===		=== Or set it to be a DHCP client ===

Adj: /* Or set it to be a DHCP client */

2015-06-29T04:58:10Z

Or set it to be a DHCP client

← Older revision		Revision as of 04:58, 29 June 2015
Line 60:		Line 60:
	host 172.16.0.254 255.255.255.0		host 172.16.0.254 255.255.255.0
	C3(rw)->		C3(rw)->

			'''Except:''' You really want to put an IP address on VLAN 1 instead. See below for how that works.

	=== Or set it to be a DHCP client ===		=== Or set it to be a DHCP client ===

Adj: /* untagged frames must flow (too) */

2015-06-29T04:43:58Z

untagged frames must flow (too)

← Older revision		Revision as of 04:43, 29 June 2015
Line 250:		Line 250:

	=== untagged frames must flow (too) ===		=== untagged frames must flow (too) ===
	Use this to set the untagged VLAN ID for a range of ports:		Use this to set the untagged ingress VLAN ID for a range of ports:
	C3(rw)->'''set port vlan ge.1.17-24 100'''		C3(rw)->'''set port vlan ge.1.17-24 100'''
	The PVID is used to classify untagged frames as they		The PVID is used to classify untagged frames as they
Line 264:		Line 264:
	-----------------------------------------------------------------		-----------------------------------------------------------------
	ge.1.17 100 N untagged: 100		ge.1.17 100 N untagged: 100
			C3(rw)->'''show vlan portinfo vlan 100'''
			Port VLAN Ingress Egress
			Filter Vlan
			-----------------------------------------------------------------
			ge.1.17 100 N untagged: 100
			ge.1.18 100 N untagged: 100
			ge.1.19 100 N untagged: 100
			ge.1.20 100 N untagged: 100
			ge.1.21 100 N untagged: 100
			ge.1.22 100 N untagged: 100
			ge.1.23 100 N untagged: 100
			ge.1.24 100 N untagged: 100
	C3(rw)->		C3(rw)->

Adj: /* delete a VLAN */

2015-06-29T03:58:26Z

delete a VLAN

@@ Line 248: / Line 248: @@
  C3(rw)->
 The listed egress ports are only those that are currently up.  Plug another link partner in on a new port and that port will be listed as an egress port, too.
 === delete a VLAN ===

Adj: /* The tagged frames must flow! */

2015-06-29T03:55:47Z

The tagged frames must flow!

← Older revision		Revision as of 03:55, 29 June 2015
Line 231:		Line 231:
	C3(rw)->		C3(rw)->

	=== ~~The tagged~~ frames must flow! ===		=== Tagged frames must flow! ===
	Set all ports on stack unit 1 to carry VLAN 900 tagged on all ports:		Set all ports on stack unit 1 to carry VLAN 900 tagged on all ports:
	C3(rw)->'''set vlan egress 900 ge.1.1-48 tagged'''		C3(rw)->'''set vlan egress 900 ge.1.1-48 tagged'''

Adj: /* delete a VLAN */

2015-06-28T16:52:32Z

delete a VLAN

@@ Line 256: / Line 256: @@
  C3(rw)->
 this one also takes VLAN ranges instead of just a single VLAN number or name
 == What time is it?  It's time for lunch! ==

Adj: /* Or set it to be a DHCP client */

2015-06-27T04:48:18Z

Or set it to be a DHCP client

← Older revision		Revision as of 04:48, 27 June 2015
Line 72:		Line 72:

	Naturally, the DHCP server's config needs some updates to include this device.		Naturally, the DHCP server's config needs some updates to include this device.

			=== You do want it to have a static IP, right? ===
			If you're weird like me and do a lot of static DHCP reservations (hey, it let's you easily change things like your DNS and NTP servers), you'll want the switch's MAC address. Find it like so:
			C3(rw)->show mac type mgmt

			MAC Address FID Port Type
			----------------- ---- ------------- --------
			00-1F-45-85-17-38 1 host Management
			C3(rw)->
			And update the DHCPD config appropriately.

	=== IPv6, anyone? ===		=== IPv6, anyone? ===