Adj: All new things here

2024-03-16T18:06:17Z

All new things here

New page

Basic firmware (BIOS/UEFI) settings.

# Power on server
# Press F2 for System Setup
# Enter System BIOS Settings
## Memory Settings > System Memory Testing: Enabled
## Memory Settings > Memory Operating Mode: Optimizer Mode
## Memory Settings > Node Interleaving: Disabled
## Memory Settings > Snoop Mode: Early Snoop
## Processor Settings > Logical Processor: Enabled
## Processor Settings > QPI Speed: Maximum
## Processor Settings > QPI Link L1 Power Management: Disabled
## Processor Settings > Virtualization Technology: Enabled
## Processor Settings > All other: default values
## SATA Settings > Embedded SATA: Off
## Boot Settings > Boot Mode: UEFI
## Boot Settings > Boot Sequence Retry: Enabled
## Boot Settings > UEFI Boot Settings > All: default values
## Network Settings > PXI Device (All): Enabled
## Network Settings > UEFI iSCSI > iSCSI Device1: Disabled
## Integrated Devices > USB: Enabled
## Integrated Devices > Integrated RAID: Enabled
## Integrated Devices > Integrated Network Card 1: Enabled
## Integrated Devices > IOAT DMA Engine: Enabled
## Integrated Devices > SI-IOV Global Enable: Enabled
## Integrated Devices > OS Watchdog Timer: Disabled
## Serial Communication > Serial Communication: Auto
## Serial Communication > Serial Port Address: Device 1=COM1, Device2=COM2
## Serial Communication > External Serial Connector: Serial Device 2
## Serial Communication > Failsafe Baud Rate: 115200
## Serial Communication > Terminal Type: VT100/VT220
## Serial Communication > Redirection After Boot: Enabled
## System Profile Settings > System Profile: Performance Per Watt (OS)
## System Security > All: Defaults
## System Security > Secure Boot: Disabled
## Miscellaneous Settings > Date/Time: set appropriately (UTC)
## Miscellaneous Settings > In-System Characterization: Enabled
# Leave System BIOS Settings
# Enter iDRAC Settings
## Network Settings > Enable NIC: Enabled
## Network Settings > NIC Selection: Dedicated
## Network Settings > Register DRAC on DNS: Disabled
## Network Settings > Auto Config Domain Name: Enabled
## Network Settings > Enable IPv4: Enabled
## Network Settings > Enable DHCP: Enabled
## Network Settings > Use DHCP to Obtain DNS server address: Enabled
## Network Settings > Enable IPv6: Enabled
## Network Settings > Enable Auto-configuration (IPv6): Enabled
## Network Settings > Use DHCPv6 to obtail DNS Server Address: Disabled
## Network Settings > Enable IPMI Over LAN: Enabled
## Network Settings > Enable VLAN ID: Disabled
## Alerts > ALL: defaults (disabled)
## Front Panel Security: Disable Power Button: No
## Media And USB Port Settings > Virtual Media Status: Auto Attach
## Media And USB Port Settings > Enable vFlash: Enabled
## Media And USB Port Settings > USB Management Port Mode: Automatic (default)
## Lifecycle Controller > Lifecycle Controller: Enabled
## Lifecycle Controller > Collect System Inventory on Restart: Enabled
## Lifecycle Controller > Cancel Lifecycle Controller Actions: No
## Power Configuration > Power Cap Policy: Disabled
## Power Configuration > Enable Hot Spare: Disabled
## Thermal > Thermal Profile: Default Thermal Profile Settings
# Leave iDRAC Settings
# Enter Device Settings
## Enter Integrated RAID Controller 1 (PERC H730 Mini)
### Advanced Controller Management > Set Factory Defaults
### Advanced Controller Management > Switch to HBA Mode (If in RAID mode only)
### Advanced Controller Properties > Disk Cache for Non-RAID: Disable
### Advanced Controller Properties > Auto Import Foreign Config: Disable
### Advanced Controller Properties > Boot Mode: Ignore errors
### Advanced Controller Properties > Abort Consistency Check on Error: Disabled
# Leave Device Settings
# Leave System Setup (reboot)

R630 configuration - Revision history

Adj: All new things here