Sun StorEdge T300 - Revision history

Adj: /* Password recovery using serial interface */

2012-10-09T21:45:15Z

Password recovery using serial interface

← Older revision		Revision as of 21:45, 9 October 2012
Line 105:		Line 105:
	* reboot device using '''<code>reboot</code>'''		* reboot device using '''<code>reboot</code>'''
	* after it boots, log in as '''<code>root</code>''' with the password just gleaned above		* after it boots, log in as '''<code>root</code>''' with the password just gleaned above
			* after logging in, the password may be changed by using the '''<code>passwd</code>''' command (changing it from the boot loader doesn't work)

Adj: /* Serial cable */

2012-10-09T21:23:37Z

Serial cable

@@ Line 24: / Line 24: @@
 |}
-This is on an RJ11-6 connector.  We'll assume the conductors are numbers 1 to 6 left to right on the female jack on the back of the T300 controller board.  (Cribbed from http://www.sunhelp.org/unix-serial-port-resources/serial-pinouts/#storedge.link)
+This is on an RJ11-6 connector.  The conductors are numbers 1 to 6 left to right on the female jack on the back of the T300 controller board.  (Cribbed from http://www.sunhelp.org/unix-serial-port-resources/serial-pinouts/#storedge.link)
 == IP address setup ==

Adj: /* Password recovery using serial interface */

2012-10-09T21:07:35Z

Password recovery using serial interface

← Older revision		Revision as of 21:07, 9 October 2012
Line 37:		Line 37:

	== Password recovery using serial interface ==		== Password recovery using serial interface ==
			* Attach serial cable to RJ11-6 port on back of controller.
	To be written.
			* Power on device.
			* Interrupt boot process -- send a ^M when the controller says
			hit the RETURN key within 3 seconds to cancel
			* Use the '''<code>set passwd</code>''' command to see what the T300's password is set to.
			* reboot device using '''<code>reboot</code>'''
			* after it boots, log in as '''<code>root</code>''' with the password just gleaned above

Adj: /* IP address setup */

2012-08-30T16:33:15Z

IP address setup

← Older revision		Revision as of 16:33, 30 August 2012
Line 31:		Line 31:
	A RARP server is needed on the same Ethernet broadcast domain to send a reply to the T300 with its IP address. http://packages.debian.org/search?keywords=rarpd lists such a package.		A RARP server is needed on the same Ethernet broadcast domain to send a reply to the T300 with its IP address. http://packages.debian.org/search?keywords=rarpd lists such a package.

	The RARP queries do not seem to be retried for very long, so the T300 needs to be on a port without spanning tree ~~turned on~~.		The RARP queries do not seem to be retried for very long (4 attempts at 2 second intervals), so the T300 needs to be on a port without a 30 spanning tree delay.

	== Management ==		== Management ==

Adj: /* Password recovery using serial interface */

2012-08-30T16:16:04Z

Password recovery using serial interface

← Older revision		Revision as of 16:16, 30 August 2012
Line 37:		Line 37:

	== Password recovery using serial interface ==		== Password recovery using serial interface ==
			To be written.

Adj: /* IP address setup */

2012-08-30T16:15:49Z

IP address setup

← Older revision		Revision as of 16:15, 30 August 2012
Line 32:		Line 32:

	The RARP queries do not seem to be retried for very long, so the T300 needs to be on a port without spanning tree turned on.		The RARP queries do not seem to be retried for very long, so the T300 needs to be on a port without spanning tree turned on.

			== Management ==
			telnet to the device. Log in as '''<code>root</code>'''. If the password is not known you'll have to dig it out using the serial interface.

			== Password recovery using serial interface ==

Adj: /* IP address setup */

2012-08-30T16:13:58Z

IP address setup

← Older revision		Revision as of 16:13, 30 August 2012
Line 30:		Line 30:

	A RARP server is needed on the same Ethernet broadcast domain to send a reply to the T300 with its IP address. http://packages.debian.org/search?keywords=rarpd lists such a package.		A RARP server is needed on the same Ethernet broadcast domain to send a reply to the T300 with its IP address. http://packages.debian.org/search?keywords=rarpd lists such a package.

			The RARP queries do not seem to be retried for very long, so the T300 needs to be on a port without spanning tree turned on.

Adj: /* Serial cable */

2012-08-30T16:12:47Z

Serial cable

← Older revision		Revision as of 16:12, 30 August 2012
Line 25:		Line 25:

	This is on an RJ11-6 connector. We'll assume the conductors are numbers 1 to 6 left to right on the female jack on the back of the T300 controller board. (Cribbed from http://www.sunhelp.org/unix-serial-port-resources/serial-pinouts/#storedge.link)		This is on an RJ11-6 connector. We'll assume the conductors are numbers 1 to 6 left to right on the female jack on the back of the T300 controller board. (Cribbed from http://www.sunhelp.org/unix-serial-port-resources/serial-pinouts/#storedge.link)

			== IP address setup ==
			The T300 can get its IP address using [http://en.wikipedia.org/wiki/Reverse_Address_Resolution_Protocol RARP]. There is a small pull-out tag inside the T300 chassis with the unit's MAC address. This tag is located in the front (the side with the drives) on the inside left wall of the unit.

			A RARP server is needed on the same Ethernet broadcast domain to send a reply to the T300 with its IP address. http://packages.debian.org/search?keywords=rarpd lists such a package.

Adj: /* Serial cable */

2012-08-26T19:58:22Z

Serial cable

← Older revision		Revision as of 19:58, 26 August 2012
Line 1:		Line 1:
	== Serial cable ==		== Serial cable ==
⚫	~~Pin~~ Function
⚫	1 Ground
⚫	~~2-3~~ Reserved
⚫	4 Ground
	5 RXD
	6 TXD

			{\|
	This is on an RJ11-6 connector
			!RJ11-6 Pin
	(Cribbed from http://www.sunhelp.org/unix-serial-port-resources/serial-pinouts/#storedge.link)
		⚫	!Function
			\|-
			\|1
		⚫	\|Ground
			\|-
			\|2
		⚫	\|Reserved
			\|-
			\|3
			\|Reserved
			\|-
			\|4
		⚫	\|Ground
			\|-
			\|5
			\|RXD
			\|-
			\|6
			\|TXD
			\|}

			This is on an RJ11-6 connector. We'll assume the conductors are numbers 1 to 6 left to right on the female jack on the back of the T300 controller board. (Cribbed from http://www.sunhelp.org/unix-serial-port-resources/serial-pinouts/#storedge.link)

Adj: Created page with "== Serial cable == Pin Function 1 Ground 2-3 Reserved 4 Ground 5 RXD 6 TXD This is on an RJ11-6 connector (Cribbed from http://www.sunhelp.org/unix-serial-p…"

2012-08-26T19:45:27Z

Created page with "== Serial cable == Pin Function 1 Ground 2-3 Reserved 4 Ground 5 RXD 6 TXD This is on an RJ11-6 connector (Cribbed from http://www.sunhelp.org/unix-serial-p…"

New page

== Serial cable ==
Pin Function
1 Ground
2-3 Reserved
4 Ground
5 RXD
6 TXD

This is on an RJ11-6 connector
(Cribbed from http://www.sunhelp.org/unix-serial-port-resources/serial-pinouts/#storedge.link)