Hiveless

I scored a couple of Aerohive HiveAP 330 WiFi access points from eBay for an agreeable price. I do not want to pay ongoing licensing fees to manage these systems. They should be usable without a connection to big brother.

First things

HiveAP 330 is a fairly cute little box, about 7in x 7in x 1.75in in size.

On the back can be found a console port (Cisco console cables work great!), two gigabit Ethernet ports (ETH0 (PoE enabled) and ETH1), a power connector, and a small reset pinhole.

Attaching the console cable, configuring Kermit for 9600-8-n-1 and no flow control, and powering the AP on, we're greeted with:

U-Boot 2009.11 (Mar 18 2014 - 16:01:33)

CPU0:  P1020E, Version: 1.1, (0x80ec0011)
Core:  E500, Version: 5.1, (0x80212051)
Clock Configuration:
       CPU0:533.333 MHz, CPU1:533.333 MHz, 
       CCB:266.667 MHz,
       DDR:266.667 MHz (533.333 MT/s data rate) (Asynchronous), LBC:16.667 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
I2C:   ready
SPI:   ready
DRAM:  Configuring DDR for 533.333 MT/s data rate
DDR: 256 MB
FLASH: 64 MB
L2:    256 KB enabled
MMC:  

    PCIE2 connected to Slot 1 as Root Complex (base addr ffe09000)
               Scanning PCI bus 01
        01  00  168c  0030  0280  ff
    PCIE2 on bus 00 - 01 

    PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000)
               Scanning PCI bus 03
        03  00  168c  0030  0280  ff
    PCIE1 on bus 02 - 03

In:    serial
Out:   serial
Err:   serial
Net:   eth0, eth1
current temperature is 21
Hit any key to stop autoboot:  0 
Password:

some quick Googling has found the U-Boot bootloader password to be administrator. (Simple is good, right?)

poking around in the boot loader

More than 3 seconds before boot

• Power on device
• Interrupt boot loader
• Enter boot loader password (administrator)
• change the environment setting:

=> setenv bootdelay 15
=> printenv
=> saveenv
=> reset

Watching it boot, should see the 3 second autoboot timeout now be 15 seconds in length.

messing around in the HiveOS CLI

Unable to log in with the default HiveOS credentials? (Admin/aerohive)? Wipe the AP's config by holding the Reset switch for 10 seconds. Here's a console transcript of that happening:

ap10-sf login: ******get interrppt from irq 47
gpio ier 800000, imr 800000
****this my gpio interrupt
[board]: Reset-button pressed!
[board]: Reset-button pressed!
[board]: Reset-button pressed!
[board]: Reset-button pressed!
[board]: Reset-button pressed!
[board]: Pressed reset-button over 5 seconds, restore the default factory configuration! 
[board]: Reset-button pressed!
[board]: Reset-button pressed!
[board]: Reset-button pressed!
[board]: Reset-button pressed!
[board]: Reset-button pressed!
Restarting system. 


U-Boot 2009.11 (Mar 18 2014 - 16:01:33)

CPU0:  P1020E, Version: 1.1, (0x80ec0011)
Core:  E500, Version: 5.1, (0x80212051)
Clock Configuration:
       CPU0:533.333 MHz, CPU1:533.333 MHz, 
       CCB:266.667 MHz,
       DDR:266.667 MHz (533.333 MT/s data rate) (Asynchronous), LBC:16.667 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
I2C:   ready
SPI:   ready
DRAM:  Configuring DDR for 533.333 MT/s data rate
DDR: 256 MB
FLASH: 64 MB
L2:    256 KB enabled
MMC:  

    PCIE2 connected to Slot 1 as Root Complex (base addr ffe09000)
               Scanning PCI bus 01
        01  00  168c  0030  0280  ff
    PCIE2 on bus 00 - 01 

    PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000)
               Scanning PCI bus 03
        03  00  168c  0030  0280  ff
    PCIE1 on bus 02 - 03

In:    serial
Out:   serial
Err:   serial
Net:   eth0, eth1
current temperature is 39
Hit any key to stop autoboot:  0